How To Change Oil For 2013 Corolla

2009-2013 Toyota Corolla 1.8L Engine Oil Change Guide
How to change the motor oil & supersede the filter on a 10th generation Toyota Corolla with the 1.8L 2ZR-FE I4 engine.

2010 Corolla 1.8 Liter I4
Twist Off Oil Filler Cap
Pull Upwards Oil Dipstick

This automotive "how-to" guide was specifically written to assist owners of the 10th generation (2009, 2010, 2011, 2012, & 2013) Toyota Corolla in changing the motor oil and replacing the cartridge oil filter in the 2ZR-FE 1.8 liter inline four cylinder engine.

Owners of other Toyota or Scion vehicles equipped with the 2ZR-FE engine such equally the Yaris, Matrix, xD, Allion, Premio, Auris and the Pontiac Vibe may also find these DIY oil change instructions to be helpful.

The items needed to complete this procedure include a floor jack, jack stands, a 14mm socket with 3/eight" drive ratcheting wrench, a 64mm oil filter wrench (AST Tools TOY 640), a 24mm socket with 1/2" drive ratcheting wrench, a new cartridge oil filter and 5 quarts of new SAE 5W-20 or 0W-twenty oil.

A few compatible cartridge oil filter elements include the post-obit with their part numbers: Toyota 04152-YZZA6, Purolator L16311, K&N PS-7021, Fram CH10358, Wix 57064, ACDelco PF1768, Mann ML 1048 and Hastings # LF640.

Jack Point - Raise Vehicle
Black Metallic Oil Pan
Silver Oil Drain Bolt The starting time steps are to warm upward the engine for a few minutes, park the vehicle on a level surface and turn off the engine. Warming up the engine will assistance suspend any contaminants inside the old oil and permit it to drain out more quickly.

Engage the emergency / parking brake and chock the rear wheels to preclude the vehicle from moving.

Pop open the hood, twist off the oil filler cap in the counter clockwise management and lift upwards the oil level dipstick. Removing the cap and lifting the dipstick will help forestall a vacuum from forming and allow the old oil to bleed out more quickly.

Raise the forepart of the vehicle with the floor jack and securely support it with the ii jack stands.

Cartridge Oil Filter Cap
Used Oil Catch Basin
Remove 14mm Bleed Commodities Slide under the passenger side of the engine with the used oil catch basin, a 14mm socket and a ratcheting wrench.

Locate the silver metal oil drain bolt at the rear edge of the black metal oil pan. Move the used oil grab container to just below the drain bolt.

Remove the oil bleed bolt by turning it counter clockwise with the 14mm socket and ratcheting wrench.

Be careful when you remove the oil drain bolt since the sometime oil may exist hot plenty to burn your skin depending on how long you lot warmed up the engine in the first step.

Onetime Oil Draining Out
Audit Metal Washer
Re-Insert Drain Commodities Permit the sometime oil to drain out for a few minutes or until it slows to an occasional drip.

Inspect the metal washer on the oil drain bolt. If it appears to be in good status, you may choose to re-use it. Otherwise, it should exist replaced with a new washer.

The OEM role number for the oil drain plug washer is Toyota 90430-12031 (likewise known equally 9043012031).

Re-insert the oil drain bolt and thread information technology in by manus in the clockwise management to forbid it from becoming cantankerous threaded.

Tighten the oil drain bolt with the 14mm socket and ratcheting wrench to just by hand tight or about 20-25 ft lbs of torque.

Tighten Oil Drain Bolt
Black Plastic Oil Filter Cap
Attach Oil Filter Wrench In guild to remove the black plastic cartridge oil filter housing, you'll need a 64mm oil filter wrench with 14 flats or "flutes" such as the AST Tools part # TOY640, Toyota SST (Special Service Tool) # 09228-06500-02, or #
Turn Counter Clockwise
Oil Draining From Filter
Twist Off Filter Housing Motion the used oil grab basin to just beneath the oil filter housing.

Attach the TOY 640 oil filter wrench to the black plastic oil filter cap. Loosen the oil filter cap by turning it counter clockwise with a 24mm socket and ane/2" drive ratcheting wrench.

This was the first oil change that I performed on my used 2010 Corolla and the oil filter cap was on extremely tight. I constitute that the filter wrench was slipping and start to round off the corners of the plastic cap.

To help create a ameliorate fit, I placed a piece of newspaper inside of the oil filter wrench and firmly tapped information technology in place on the oil filter cap with a prophylactic mallet. (Make sure that you are trying to turn the cap counter clockwise to loosen it.)

If that nevertheless doesn't help you loosen the filter cap, y'all may need to utilize a longer ratcheting wrench for more leverage. A last resort would exist to use a meaty one/2" drive electric or compressed air impact wrench with the 24mm socket fastened.

04152-YZZA6 Oil Filter
Dip Finger In New Oil
Lubricate Rubber O-Band Dip your pinky finger in some new SAE 5W-xx or 0W-20 oil and lubricate the new condom o-ring gasket. Lubricating the new o-band volition help it form a meliorate seal and make it easier to remove the cap at the side by side oil alter.
Pull Out Old Filter
Wipe Out Oil Filter Housing
Remove Old Rubber O-Band Pull the old cartridge oil filter out of the housing and pry the old safe o-ring off the bottom of the threads with a pocket-size flathead screwdriver.

I'd recommend using either the genuine Toyota 04152-YZZA6 oil filters or the K&North PS-7021 filter since they accept the best reviews on Amazon.

Push the new rubber o-band on the oil filter cap until it rests at the bottom of the threads.

Install New O-Ring Gasket
Push In New Cartridge Filter
New Filter Installed Push the new cartridge oil filter element in to the oil filter housing.
Twist On Clockwise
Tighten With 24mm Socket
Tap Off 64mm Wrench Twist on the oil filter cap in the clockwise direction by manus to prevent it from condign cross threaded.

Tighten the oil filter cap with the 24mm socket and ratcheting wrench to about 1/4 to 1/2 plow past hand tight or about 18 ft lbs of torque.

If the oil filter wrench is stuck to the cap, tap it off with a condom mallet.

Double check that the oil drain bolt and oil filter cap are tight before moving on to the next steps.

Lower Front of Vehicle
Insert Automotive Funnel
Pour In SAE 5W-xx Oil Lower the front of the vehicle from the jack stands using the floor jack.

Insert an automotive funnel in to the oil filler hole and pour in almost 4 quarts of the engine's 4.4 U.S. quart total capacity for an oil change with filter change. (The 4.four US quarts engine oil capacity equals 4.2 liters or 3.7 Imperial quarts.)

It is far better to have less than enough oil in an engine than too much. Yous may not demand to pour in the unabridged 4.4 United states of america quarts total capacity depending on how long you allowed the onetime oil to bleed out in the first step.

Twist On Oil Filler Cap
Bank check Oil Dipstick Level
"MAINT REQD" Light Temporarily supercede the oil filler cap, run the engine for a few minutes, shut it off, and let the oil to drain down to the oil pan for at least five minutes.

Cheque the level on the yellow handled dipstick and slowly add more than oil until the level reaches at or simply below the upper dot on the dipstick.

Replace the oil filler cap.

Press Odo/Trip Button
"Trip A" Displayed
Dashes Blinking Away To reset the "MAINT REQD" (maintenance required) low-cal on the commuter's instrument brandish panel, first printing the "Odo/Trip" button to display "Trip A". Then turn the ignition to "Off", printing and hold the Odo/Trip button, and turn the ignition switch to the "On" position simply don't commencement the engine.

You should see half-dozen dashes flashing equally they disappear and and then 6 zeroes will briefly wink on the brandish. The "Maint Reqd" light should now exist off.

Exist certain to record the oil modify in your vehicle'south service records. It's also a proficient idea to watch your driveway or parking spot for drops of oil and cheque the oil level on the dipstick during the next few days.

For more than, check out my other Corolla DIY tutorials at the links below -

2009-2013 Toyota Corolla Repair & Maintenance Guides

2003-2008 Toyota Corolla Repair & Maintenance Guides

Source: https://www.paulstravelpictures.com/2009-2013-Toyota-Corolla-2ZR-FE-Engine-Oil-Change-Guide/

Posted by: northingtondarke1993.blogspot.com